Welded Mesh Inspection Quiz

Test

Jugadas 1

Crear copia

Sobre esta actividad

Learn inspection basics

Creada por

GRAFIMALLAS SAS

Colombia

Descarga la versión para jugar en papel

Top 10 resultados

#	Jugador	Acierto	tiempo
1	Anónimo 26 de Agosto de 2026	% 80	02:55

¿Quieres aparecer en el Top 10 de este juego? Inicia sesión para identificarte.

Crea tu propio juego gratis desde nuestro creador de juegos

Compite contra tus amigos para ver quien consigue la mejor puntuación en esta actividad

Crear reto

Cultura general española

Ernest Serret

España

(101)

Responde las siguientes preguntas
Verbos irregulares en Inglés

Hélmer González Serrano

Colombia

(314)

Se presentan 10 preguntas, cada una con 4 opciones de respuesta. Seleccione la que considere correcta.
Brawl stars preguntas

Carlos Andrés Prieto Rodríguez

Colombia

(165)

Completa todas las preguntas
Tipos de sintagmas (II)

idoia rubio

España

(945)

Actividades interactivas para reconocer los distintos tipos de sintagmas
cuanto sabes de Futbol

hugo estay

Chile

(322)

este test esta basado en las diapositivas que pudimos ver con anterioridad, consta de 10 preguntas las cuales tienen alternativas para poder resolverlas.

		%
	Anónimo	%
		%
		%

Imprime tu juego

Welded Mesh Inspection Quiz


Welded Mesh Inspection QuizVersión en línea Learn inspection basics por GRAFIMALLAS SAS 1 What is welded mesh (malla electrosoldada)? a A product welded only at edges b A fabric woven from wires c A product formed by wires joined at intersections by resistance welding d A mesh knitted from fibers 2 Which instrument is primarily used to verify the wire diameter? a Caliper (vernier caliper) b Tape measure c Microscope d Ruler 3 True or False: Visual inspection alone is enough to declare conformity. a True b Sometimes true c Only for small products d False 4 Which document(s) help determine acceptance criteria for the mesh? a Customer email notes b Only the technical sheet c Ficha técnica, order of production, and contractual/specifications d Only the production order 5 What dimensions are checked as part of the mesh inspection? a Color and texture b Longitudinal and transverse wire separation c Edge cutting length d Woven pattern 6 If a measurement indicates nonconformity, what is the recommended action? a Release as conforming if close enough b Do not release; segregate and document the nonconformity c Ignore the measurement if it looks fine d Re-measure only if asked by the client 7 Name one instrument besides a caliper used for inspection measurements. a Verifying gauge b Flexometer c Protractor d Screw gauge 8 If the nominal diameter is 4.0 mm and a measured diameter is 4.02 mm, what should you do? a Adjust the measurement to 4.00 mm b Declare conforming because it’s close c Discard the part d Verify against the specified tolerance; do not assume conformity 9 What are common visual defects to check in welds? a No visual defects are expected b Color variance only c Intersections without welds, burnt/deteriorated wires, ruptures, deformations d Only check labeling 10 What steps follow a detected nonconformity? a Identify, segregate, register, and evaluate per the nonconformity procedure b Rewind the production line to start c Ignore and proceed d Seal the product and ship it anyway Feedback 1 Welded mesh uses resistance welding at intersections, not seams or weaving. 2 A caliper provides precise measurements for small diameters. 3 Conformity requires comparison with spec and possibly other tests; visual alone is not sufficient. 4 Acceptance should be based on the technical sheet, production order, and contractual specs. 5 Separation between wires in both longitudinal and transverse directions is inspected. 6 Nonconformities must be detected, segregated, and documented per procedure. 7 A flexometer is commonly used to measure length, width, and spacing. 8 Close measurements must be checked against the tolerance before deciding conformity. 9 Visual inspection should catch weld/intersection defects, not just appearance. 10 Nonconformities require identification, segregation, recording, and evaluation.

Puedes integrar el juego en un LMS compatible con LTI 1.1 o LTI 1.3 como Canvas, Moodle, o Blackboard. De esta manera podrás guardar las puntuaciones automáticamente en el libro de calificaciones de esa plataforma.

Welded Mesh Inspection Quiz

Test

Sobre esta actividad

Creada por

Descarga la versión para jugar en papel

Top juegos

Test

Cultura general española

Test

Verbos irregulares en Inglés

Test

Brawl stars preguntas

Test

Tipos de sintagmas (II)

Test

cuanto sabes de Futbol

Welded Mesh Inspection QuizVersión en línea

por GRAFIMALLAS SAS

What is welded mesh (malla electrosoldada)?

Which instrument is primarily used to verify the wire diameter?

True or False: Visual inspection alone is enough to declare conformity.

Which document(s) help determine acceptance criteria for the mesh?

What dimensions are checked as part of the mesh inspection?

If a measurement indicates nonconformity, what is the recommended action?

Name one instrument besides a caliper used for inspection measurements.

If the nominal diameter is 4.0 mm and a measured diameter is 4.02 mm, what should you do?

What are common visual defects to check in welds?

What steps follow a detected nonconformity?

Feedback