DFM Challenge

Test

Jugadas 1

Crear copia

Sobre esta actividad

Test your knowledge of Design for Manufacture principles.

Creada por

ATIKAH HJ AWANG @ HJ MOHD RAMLI

Malasia

Descarga la versión para jugar en papel

Top 10 resultados

#	Jugador	Acierto	tiempo
1	ATIKAH HJ AWANG @ HJ MOHD RAMLI 6 de Febrero de 2026	% 100	01:25

¿Quieres aparecer en el Top 10 de este juego? Inicia sesión para identificarte.

Crea tu propio juego gratis desde nuestro creador de juegos

Compite contra tus amigos para ver quien consigue la mejor puntuación en esta actividad

Crear reto

Cultura general española

Ernest Serret

España

(100)

Responde las siguientes preguntas
Brawl stars preguntas

Carlos Andrés Prieto Rodríguez

Colombia

(164)

Completa todas las preguntas
Tipos de sintagmas (II)

idoia rubio

España

(945)

Actividades interactivas para reconocer los distintos tipos de sintagmas
Verbos irregulares en Inglés

Hélmer González Serrano

Colombia

(311)

Se presentan 10 preguntas, cada una con 4 opciones de respuesta. Seleccione la que considere correcta.
cuanto sabes de Futbol

hugo estay

Chile

(316)

este test esta basado en las diapositivas que pudimos ver con anterioridad, consta de 10 preguntas las cuales tienen alternativas para poder resolverlas.

		%
	Anónimo	%
		%
		%

Imprime tu juego

DFM Challenge


DFM ChallengeVersión en línea Test your knowledge of Design for Manufacture principles. por ATIKAH HJ AWANG @ HJ MOHD RAMLI 1 A defect is detected during assembly, but originates from geometry. Where should it have been prevented? a Assembly b Tooling sign-off c Production d Design freeze 2 Trimming flash after moulding is an example of ___________ a Defect prevention b Quality assurance c Secondary process d Process Optimisation 3 Why are some defects not visible in CAD drawings? a CAD is inaccurate b Material and process behaviour cannot be represented in CAD drawings. c Designer oversight d Simulation was not run 4 Which option most often creates recurring cost? a Design change b Secondary process c Tooling compensation d Early material review 5 If a defect relies on careful assembly to avoid damage, what does that indicate? a Operator training issue b Incomplete design c Assembly problem d Quality control issue 6 Draft angles in molded parts primarily aid which process? a Ejecting the part from the mold b Enhancing chemical resistance c Improving heat transfer d Increasing rigidity in service 7 Tolerance strategy in DFM aims to: a Place tighter tolerances only where needed b Eliminate all tolerances c Tighten tolerances everywhere d Relax tolerances beyond any functional need 8 Flow lines most strongly indicate an issue with a Machine condition b Geometry and flow path c Operator skill d Inspection method 9 Which statement best reflects DFM thinking? a Fix defects where they appear b Train operators better c Improve inspection accuracy d Question decisions that allowed defects 10 What is the main purpose of DFM a Reduce tooling cost b Optimise machine settings c Improve inspection results d Prevent problems before production 11 Spring back should primarily be addressed at which stage? a Tooling sign-off b Inspection c Production d Asembly 12 Why do secondary processes increase manufacturing cost? a They increase scrap b They slow inspection c They repeat every cycle d They affect material price

Puedes integrar el juego en un LMS compatible con LTI 1.1 o LTI 1.3 como Canvas, Moodle, o Blackboard. De esta manera podrás guardar las puntuaciones automáticamente en el libro de calificaciones de esa plataforma.

DFM Challenge

Test

Sobre esta actividad

Creada por

Descarga la versión para jugar en papel

Top juegos

Test

Cultura general española

Test

Brawl stars preguntas

Test

Tipos de sintagmas (II)

Test

Verbos irregulares en Inglés

Test

cuanto sabes de Futbol

DFM ChallengeVersión en línea

por ATIKAH HJ AWANG @ HJ MOHD RAMLI

A defect is detected during assembly, but originates from geometry. Where should it have been prevented?

Trimming flash after moulding is an example of ___________

Why are some defects not visible in CAD drawings?

Which option most often creates recurring cost?

If a defect relies on careful assembly to avoid damage, what does that indicate?

Draft angles in molded parts primarily aid which process?

Tolerance strategy in DFM aims to:

Flow lines most strongly indicate an issue with

Which statement best reflects DFM thinking?

What is the main purpose of DFM

Spring back should primarily be addressed at which stage?

Why do secondary processes increase manufacturing cost?